Görüntüleme
13
İndirme
1
Bu çalışmada yüksek fırın cürufu partiküllerinin epoksi matris içine katılarak oluşturulan polimer matrisli kompozitin aşınma dayanımına etkisi araştırılmıştır. Karşılaştırma yapmak amacıyla yüksek fırın cürufu takviyeli kompozit yanında Al2O3 katkılı epoksi matrisli kompozitler üretilmiştir. Takviye edici partikül olarak 61 μm, 91 μm ve 125 μm boyutunda yüksek fırın cürufu ve Al2O3 tozları, %30 oranında epoksi reçine içine karıştırılmıştır. Oda sıcaklığında 36 saat kürleme işlemine bırakılan numuneler ball-on disk aşınma cihazında aşınma işlemine tabi tutulmuştur. 10N, 15N ve 20N yükler altında 300 m aşınma işlemi uygulanan numunelerde yüksek fırın cürufu katkılı kompozitin Al2O3 katkılı kompozitle kıyaslanarak aşınma ve sürtünme davranışı incelenmiştir. Aşınma yüzeylerinde meydana gelen hacim kayıpları ve muhtemel aşınma mekanizmaları SEM mikroskobu ile incelenmiştir. Aşınma testleri sonucunda özellikle düşük yüklerde olmak üzere tüm yükler altında yüksek fırın cürufu takviyeli kompozitin aşınma kayıpları Al2O3‘e oranla daha düşük çıkmıştır. Artan yüke bağlı olarak kompozitlerin aşınma dayanımları arasındaki fark azalmıştır. Artan yüke bağlı olarak batıcı uçun numune üstünde oluşturduğu kuvvetlerin artması, tüm numunelerde aşınma hacim kayıplarını artırmıştır. Takviye edici partikül boyutunun artması matris-partikül tutunmasını zayıflattığı ve daha az alanda var olduğu için kompozitlerin aşınma dayanımında düşüşe sebep olmuştur. Yüksek fırın cürufu takviyeli kompozitlerde baskın aşınma türü olarak plastik deformasyon görülürken, Al2O3 takviyeli kompozitlerde yüzey altı yorulması aşınma mekanizması baskın olarak görülmüştür.
This study has studied the impact of high oven curve particles on the resistance of the polymer matrix composite created by participating in the epoxy matrix. For the purpose of comparing, high oven curve supplement composite along with Al2O3 contributed epoxy matrix composites were produced. As a supplementary particle, 61 μm, 91 μm and 125 μm high oven curve and Al2O3 powder are mixed in 30% epoxy rhinus. The samples left for 36-hour curling process at room temperature were subjected to curling process in the ball-on disk curling device. In samples under 10N, 15N and 20N loads, the 300m stretching process was applied, compared with the Al2O3 contributed composite of the high oven curve contributed composite, the stretching and stretching behavior was studied. Volume losses occurring on scratching surfaces and possible scratching mechanisms have been studied with a SEM microscope. As a result of scratching tests, the scratching losses of the high oven curve supplement composite under all loads, especially in low loads, were lower than Al2O3. Depending on increased load, the difference between the compounds' stretching resistance has decreased. Depending on the increased load, the increase in the forces that the immersive end forms on the sample has increased the loss of the exhaust volume in all samples. The increase in the size of the complementary particle has led to a decrease in the stretching resistance of the composites because it weakens the matrix-particular retention and is present in less area. While plastic deformation is seen as a dominant type of stretching in high oven curve supplement composites, the sub-performance stretching mechanism is seen as dominant in Al2O3 supplement composites.
Polymer matrix composites are advanced materials that can be used in a variety of applications such as low density, high strength, automobile, aerospace and home appliances. Common and commercially used composites generally use polymers as matrix materials and are commonly known as resin solutions. variety of polymer materials are available as matrix type and the commonly used matrix materials are epoxy, urethane, polyamide, polyester, polyether ether ketone (PEEK)… The reinforcement materials used are generally fibers, particles and ground minerals. Due to the increasing production of iron and steel, high levels of slag are emerging and pose problems for both producers and the environment. From this point of view, in this study, it has been investigated on the wear behavior of the epoxy matrix as a reinforcement in order to evaluate the blast furnace slag (BFS), which is known to have hard ceramic components. EP100 epoxy resin and EP385H hardener are commercially available. The epoxy resin was selected as matrix and Al2O3 and blast furnace slag dusts of 61 µm, 91 µm and 125 µm were used as reinforcement (Table 1). In the produced composites the reinforcement ratio was kept constant at 30% and the epoxy and reinforcement powders were mixed until a homogeneous mixture was obtained. The curing agent was added during the mixture and at the end of the process the mixture was poured into the silicone mold. The samples were then allowed to cure for 36 hours at room temperature. Dry sliding wear behavior of samples tested with ball on disc wear device. The wear resistance of the composites reinforced with blast furnace slag at all conditions was higher than the samples reinforced with Al2O3. However, the volume losses of composites reinforced with blast furnace slag especially at low loads are much lower than the samples reinforced with Al2O3. The reason for this; It can be shown that the blast furnace slag having a fragile structure is broken under high load and divided into many sharp edges and these particles contribute to abrasion by acting as abrasive material in front of the abrasive ball. The volume losses of the samples increased with increasing load. Because the two forces during wear affect the wear losses. One of them is the force acting on the counter-surface of the ball, while the other is the shear force. The increase of the load increased the penetration of abrasive ball to the opposite surface. Therefore, the amount of material to be affected during the relative movement of the abrasive ball is also increased. As a result, if sufficient shear force occurs, it transfers more mass from the ball to the surface. In both types of composite, increased reinforcement particle size resulted in increased wear losses. Low size reinforcement particles are more homogeneously distributed in the matrix at more points. In this case abrasive ball will be more difficult to penetrate into the matrix and will contribute more to the wear resistance of the low-dimensional particle reinforced composite material. In addition, low-dimensional particles will have more adhesion in the matrix. This will help reduce wear losses. Both Al2O3 and blast furnace slag reinforced composites showed fatigue related surface deterioration and plastic deformation wear mechanisms. However, plastic deformation was the predominant wear mechanism in blast furnace slag reinforced composites, while Al2O3 reinforced composites were predominantly identified as a fatigue-related surface damage wear mechanism.
Alan : Mühendislik
Dergi Türü : Ulusal
Makale Detay 
Benzer Makaleler
PDF Görüntüle
Dergi Bilgisi
Eseri Dinleyin
Alıntı Yap
Bu Sayfayı Yazdırın
Paylaş
Mendeley
