Amaç: Bu çalışmanın amacı sinterize öncesi ve sinterize sonrası zirkonyum oksit esaslı seramikler üzerine uygulanan farklı yüzey işlemlerinin yüzey pürüzlülüğüne olan etkisini araştırmaktır. Gereç ve Yöntemler: Çalışmada toplam 150 adet disk şeklinde örnekler CAD_CAM cihazında hazırlandı. Önekler 7 gruba bölündü ( n:10): Kontrol grubu, kumlama, Er-YAG lazer, Nd-YAG lazer, Er-YAG lazer + Kumlama, Nd-YAG lazer + kumlama, ince ve kalın grenli frez. Örneklerin yarısına sinterizasyon öncesi yüzey işlemleri uygulanıp sinterlendi. Diğer yarısına ise sinterizasyon sonrası yüzey işlemi uygulandı. Kontrol grubuna herhangi bir yüzey işlemi uygulanmadı ve sadece sinterlendi. Örneklerin yüzey pürüzlülüğü profilometre cihazı ile ölçüldü ve yüzeylerinde olan değişiklikler taramalı elektron mikroskobu ile incelendi. Bulgular: Çalışmada elde edilen veriler Varyans analizi, Tukey testi ve eşler arası önemlilik testi ile analiz edildi (p=0,05). Sinterizasyon öncesi uygulanan yüzey işlemlerinden frez uygulanan gruplar hariç kontrol grubu ile kıyaslandığında yüzey pürüzlülüğünü istatistiksel olarak anlamlı arttırdığı görüldü (p<0,05). Sinterizasyon sonrası uygulan yüzey işlemlerinde ise ince grenli frez haricindeki tüm grupların yüzey pürülülüğünü istatistiksel olarak anlamlı arttırdığı görüldü (p<0,05). Sinterizasyon öncesi yüzey uygulamaları sinterizasyon sonrası uygulamalarına göre daha etkili bulundu. Sonuç: Çalışmada sinterizasyon öncesi uygulanan tüm yüzey işlemleri ve özellikle Er-YAG lazer+ kumlamanın pürüzlülük değerini oldukça arttırdı. Bu sebeple mikromekanik bağlantıyı da artırabileceği sonucu çıkarılabilir. Anahtar kelimeler: zirkonyum oksit, yüzey pürüzlülük, kumlama, lazer, frez
Purpose: The purpose of this study is to investigate the effects of the various surface processes applied to pre-synthetic and post-synthetic zirconium oxide-based ceramics on the surface smoothness. Tools and Methods: In the study, a total of 150 discs formed samples were prepared on the CAD_CAM device. The subjects were divided into 7 groups (n:10): Control group, welding, Er-YAG laser, Nd-YAG laser, Er-YAG laser + welding, Nd-YAG laser + welding, thin and thin grened frez. Half of the examples were implemented and synthesized before synthesization surface processes. The other half was performed after the surface process. No surface process was applied to the control group and was only synthesized. The surface smoothness of the samples was measured by the profilometer device and the changes in their surfaces were studied by an electron microscope scanned. Results: The data obtained in the study was analyzed through the Varyans analysis, the Tukey test and the interpersonal importance test (p=0,05). When compared with the control group, except the groups applied frez from the surface processes applied prior to synthesis, the surface smoothness was statistically significantly increased (p<0,05). In the surface processes applied after synthesis, all groups except the thin grened frez were statistically significantly increased surface purity (p<0,05). Pre-sinterization surface applications were found more effective than post-sinterization applications. Result: The study significantly increased the smoothness of all the surface processes applied before synthesis, and in particular the Er-YAG laser+ assembly. This can also result in an increase in the micromekanic connection. Keywords: zirconium oxide, surface smoothness, slurry, laser, frez
Alan : Sağlık Bilimleri
Dergi Türü : Ulusal
Benzer Makaleler | Yazar | # |
---|
Makale | Yazar | # |
---|