Magnezyum hafif olması, dayanıklılığı ve özellikle özgül dayanım oranının yüksekliği bakımından çelik ve alüminyum gibi yapısal metallerin yerini almaya başlamaktadır ve plastik şekil verme yöntemleriyle şekillendirilmesi ticari öneme sahiptir. Bu yöntemlerden birisi olan ekstrüzyon genelde hafif metallere uygulanan, iş parçasını bir kovan içerisine koyarak, zımba vasıtasıyla metale baskı uygulayarak ürün geometrisine sahip bir kalıp içerisinden malzemenin geçirilmesi ile gerçekleştirilmektedir. Ekstrüzyon yönteminde uygulanacak şekillendirme kuvvetinin bilinmesi kalıp malzemesi seçimi ve uygun pres kapasitesinin belirlenmesinde önemli bir etkendir. Bu çalışmada, aynı ekstrüzyon oranına sahip kalıplarla gerçekleştirilen ekstrüzyonda, kalıp giriş çapı, kalıp açısı ve kalıp kanal uzunluğu gibi kalıp parametrelerinin ekstrüzyon kuvvetine olan etkisi Taguchi L9 Ortogonal Deney Tasarımı kullanılarak incelenmiştir. Bu amaçla, 3 farklı seviyede kalıp parametreleri değerlendirilmiştir. Deneysel çalışma, aynı bilgiyle daha az deney yaparak deney zamanını düşürmek amacıyla Taguchi yöntemi kullanılarak 27 adet olması gereken deney sayısı 9 adet deneye indirgenmiştir. Sonuçlar üzerine kararlar alınmasında ise Varyans analizi (ANOVA) istatistiksel yöntemleri kullanılmıştır. Yapılan değerlendirmede, ekstrüzyon kuvveti üzerinde en fazla etki eden kalıp parametresinin %68,48 oranında kalıp giriş çapı olduğu görülmüştür. Bunun yanı sıra, ekstrüzyon kuvvetinin kalıp giriş çapının düşmesiyle artış gösterdiği, kalıp açısının artışıyla ekstrüzyon kuvvetinin azaldığı ve kalıp kanal uzunluğu arttıkça şekillendirme için gereken kuvvet arttığı tespit edilmiştir. Sonuç olarak, farklı kalıp parametrelerinin ekstrüzyon kuvveti ile olan etkileşimi belirlenmiş ve en düşük ekstrüzyon kuvvetini verebilecek uygun kalıp tasarımı optimize edilmiştir.
Magnesium is light, and in terms of its durability and especially its high resilience rate, it begins to replace structural metals such as steel and aluminum, and its shaping with plastic shaping methods has commercial importance. Extrusion, which is one of these methods, is usually applied to light metals, by placing the work piece in a cave, by applying the metal pressure through the cave, by passing the material from a pattern with product geometry. The knowledge of the shaping force to be applied in the extraction method is an important factor in the selection of the template material and determination of the appropriate pressure capacity. In this study, the effect on the extraction force of the template parameters, such as the input diameter of the template, the angle of the template and the length of the template channel, was studied in the extraction with the same extraction rate patterns using the Taguchi L9 Orthogonal Experimental Design. For this purpose, 3 different levels have been evaluated and parameters have been evaluated. The experimental study has reduced the number of experiments to 27 using the Taguchi method to reduce the time of the experiment by performing less experiments with the same information to 9 experiments. The results were determined by the statistical methods of Varyans Analysis (ANOVA). In the assessment, the most influential pattern parameter on the extrusion force was 68.48% of the pattern entrance diameter. In addition, it has been found that the extraction force increases with the fall of the template input diameter, the extraction force decreases with the increase of the template angle, and the strength needed to shape increases with the length of the template channel. As a result, the interaction of different pattern parameters with the extraction force has been determined and the appropriate pattern design that can provide the lowest extraction force has been optimized.
Alan : Mühendislik
Dergi Türü : Ulusal
Benzer Makaleler | Yazar | # |
---|
Makale | Yazar | # |
---|