Bu çalışma, bir depremden sonra performansa dayalı yapısal değerlendirme için, atık betondan dönüştürülmüş agreganın ikame edildiği beton ile üretilmiş (i) göçme modu eğilme olup kompozit donatılı, (ii) göçme modu kesme olup kompozit donatılı kolonların kırılganlık eğrilerinin elde edilmesini içermektedir. Elde edilen kırılganlık fonksiyonlarının birbirleri ile karşılaştırılması sonucunda göçme modunun farklı olması durumunun geri dönüştürülmüş agrega ikame edilen beton ile üretilmiş kolonların kırılganlık eğrileri üzerindeki etkisi ortaya çıkarılmıştır. Diğer taraftan, (i) bendinde belirtilen kolon tipi için elde edilen kırılganlık eğrilerinin Goksu (2021) tarafından yapılan çalışmada elde edilen kırılganlık eğrileri (geri dönüştürülmüş agrega ikame edilen beton ile üretilmiş, göçme modu eğilme olup konvansiyonel donatılı kolon ve çerçevelerin kırılganlık eğrileri) ile karşılaştırılması sonucunda donatı farkının bu tip yapısal elemanların kırılganlık eğrileri üzerindeki etkisi ortaya çıkarılmıştır. Bu çalışmada, veri olarak, literatürde yer alan geri dönüştürülmüş agrega ikame edilen kolon ve çerçevelerde deprem tipi yüklemeden sonra meydana gelen hasar türleri kullanılmıştır. Öteleme oranı, talep parametresi olarak dikkate alınmıştır. Sonuç olarak, göçme modu ve donatı tipi farketmeksizin geri dönüştürülmüş agrega ikame edilen tüm kolonlar için veritabanındaki düşük eksenel yüke maruz kalan kolonlarda daha büyük deformasyonların meydana geldiği, yüksek eksenel yüke maruz kalan kolonlarda “ileri hasar” ile ilgili olan öteleme oranlarının ise daha erken geliştiği tespit edilmiştir. Göçme modları aynı olup (eğilme) donatı tipleri farklı (kompozit veya konvansiyonel) olan, geri dönüştürülmüş agrega ikame edilen kolonların kırılganlık eğrilerinin özellikle ileri hasarı temsil eden hasar durumu için farklılık gösterdiği, bu farklılığın kompozit donatılı numunelerin rijitliğinin konvansiyonel donatılı numunelere göre daha fazla olmasından kaynaklanabileceği tespit edilmiştir.
This study, for the performance-based structural assessment after a earthquake, involves (i) immigration mode inclination produced with concrete where the waste converted aggregate is housed and composite equipped, (ii) immigration mode cutting and the achievement of the vulnerability curves of the composite equipped columns. As a result of the comparison of the achieved vulnerability functions with each other, the impact of the columns produced with refined concrete in the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state of the state. On the other hand, the comparison of the vulnerability curves obtained for the column type referred to in (i) point with the vulnerability curves obtained in the study by Goksu (2021) (produced with re-converted aggregate residential concrete, migration mode curves and the vulnerability curves of conventional-equipped columns and frameworks) revealed the effect of the equipment difference on the vulnerability curves of this type of structural elements. In this study, as data, the recycled agrega included in the literature used the types of damage that occur after the earthquake type is charged in the colon and frame. The ratio is considered as the demand parameter. As a result, it was found that greater deformations occurred in columns exposed to low axle load in the database for all columns in which the recycled aggregate, regardless of the mode of migration and type of equipment, and that the deformation rates related to "precedent damage" in columns exposed to high axle load developed earlier. The migration modes are the same and the equipment types are different (composite or conventional), the fragility curves of the recycled aggregate columns are different for the damage status, especially the advanced damage, this difference may be caused by the greater frequency of the composite-equipped samples than the conventional-equipped samples.
Alan : Mühendislik
Dergi Türü : Ulusal
Benzer Makaleler | Yazar | # |
---|
Makale | Yazar | # |
---|