Al-17Si, Al-17Si-0,1Sr ve Al-17Si-0,1Sr-0,6Mg alaşımları kokil kalıba döküm yöntemi ile üretilmiştir. Alaşımların yapısal ve mekanik özellikleri üretilen alaşım külçelerinden talaşlı imalat yöntemiyle hazırlanan numuneler üzerinde yapılan incelemeler ile belirlenmiştir. İçyapı incelemeleri standart metalografik yöntemler ile hazırlanan ancak dağlama yapılmayan numuneler üzerinde gerçekleştirilmiştir. İncelenen alaşımların sertlik değerleri Brinell sertlik ölçüm yöntemi, mekanik özelikleri ise üniversal bir çekme deneyi makinesinde yapılan testler yardımıyla belirlenmiştir. İkili Al-17Si alaşımının içyapısının alüminyumca zengin α dendiritleri, primer silisyum, ötektik Al-Si ve β fazlarından oluştuğu, üçlü Al-17Si-0.1Sr alaşımının içyapısının ise ikili Al-17Si alaşımındaki fazlara ek olarak AlxSiySrz fazını içerdiği görülmüştür. Üçlü Al-17Si-0.1Sr alaşımına %0.6 oranında yapılan magnezyum katkısının ise bu alaşımın içyapısında Mg2Si fazının oluşmasına yol açtığı gözlenmiştir. Al-17Si alaşımının sertlik, akma dayanımı, çekme dayanımı ve kopma uzaması değerleri sırasıyla 57 BSD, 93.7 MPa, 127.6 MPa ve %2.4, olarak ölçülmüştür. Bu değerler Al-17Si-0,1Sr alaşımında 55 BSD, 95.2 MPa, 137.9 MPa ve %2.9, Al-17Si-0.1Sr-0.6Mg alaşımında ise sırasıyla 70 BSD, 123.2 MPa, 141.1 MPa ve %1.1 olarak ölçülmüştür. Stronsiyum katkısının ikili Al-17Si alaşımının sertliğini çok az da olsa düşürdüğü, akma ve çekme dayanımı ile kopma uzaması değerlerini ise iyileştirdiği görülmüştür. Magnezyum katkısının ise üçlü Al-17Si-0.1Sr alaşımının akma ve çekme mukavemetini önemli ölçüde artırdığı ancak, kopma uzamasını azalttığı belirlenmiştir. Stronsiyum ve stronsiyum-magnezyum katkılarının Al-17Si alaşımının mekanik özelliklerine etkisi alaşımların yapısal özelliklerine dayandırılarak açıklanmıştır.
Al-17Si, Al-17Si-0,1Sr and Al-17Si-0,1Sr-0,6Mg alloys are produced with the method of casting in the moisture. The structural and mechanical characteristics of the alloys are determined by examinations made on samples prepared by the fabrication method of the produced alloys. Internal examinations have been carried out on samples prepared with standard metallographic methods but not dispersed. The hardness values of the studied alloys are determined by the Brinell hardness measurement method, and their mechanical properties are determined by the help of tests performed in a universal drawing test machine. The interior of the double Al-17Si alloy is made up of aluminum-rich α dendrites, primary silicon, ethetic Al-Si and β phases, triple Al-17Si-0. The internal structure of the 1Sr alloy has been found to contain the AlxSiySrz phase in addition to the phases in the two Al-17Si alloy. The contribution of 0.6% of magnesium to the triple Al-17Si-0.1Sr alloy has been observed to lead to the formation of the Mg2Si phase in the interior of this alloy. Al-17Si alloy’s hardness, flow resistance, drag resistance and break extension values were measured as 57 BSD, 93.7 MPa, 127.6 MPa and 2.4% respectively. These values were measured as 55 BSD, 95.2 MPa, 137.9 MPa and 2.9% in Al-17Si-0.1Sr-0.6Mg alloys, respectively 70 BSD, 123.2 MPa, 141.1 MPa and 1.1%. Strontium contributions have been shown to reduce the hardness of the double Al-17Si alloy very little, and it has improved its flow and pull resistance and break extension values. The contribution of magnesium has been determined to significantly increase the flow and pull strength of the triple Al-17Si-0.1Sr alloy, but to reduce the break extension. The effect of strontium and strontium-magnesium contributions on the mechanical properties of the Al-17Si alloy is explained based on the structural properties of the alloys.
Al-17Si, Al-17Si-0,1Sr and Al-17Si-0.1Sr-0,6Mg alloys were produced by permanent mold casting method. The structural and mechanical properties of the alloys were determined by the investigations carried out on specimens prepared by machining of the produced alloy ingots. The microstructural examinations were carried out on specimens prepared by standard metallographic methods but without etching. Their hardness and mechanical properties were determined by Brinell hardness measurement method and universal tensile tests, respectively. The microstructure of the binary Al-17Si alloy consisted of aluminum-rich α dendrites, primary silicon, eutectic Al-Si and βphases. Ternary Al-17Si-0.1Sr alloy contained AlxSiySrz phase in addition to phases in the binary Al-17Si alloy. It was observed that the 0.6% magnesium addition to the ternary Al-17Si-0.1Sr alloy cause to form of Mg2Si phase in the microstructure of this alloy. The values of the hardness, yield strength, tensile strength and elongation to fracture of Al-17Si alloy were measured as 57 BSD, 93.7 MPa, 127.6 MPa and 2.4%, respectively. These values were measured as 55 BSD, 95.2 MPa, 137.9 MPa and 2.9% in Al-17Si-0.1Sr alloy and 70 BSD, 123.2 MPa, 141.1 MPa and 1.1% in Al-17Si-0.1Sr-0.6Mg alloy. The addition of strontium reduced the hardness of the binary Al-7Si alloy to a lesser degree but improved the yield and tensile strength and elongation to fracture values. Magnesium addition significantly increased the yield and tensile strength of the ternary Al-17Si-0.1Sr alloy but decreased their elongation to fracture. The effects of strontium and strontium-magnesium additions on the mechanical properties of the Al-17Si alloy were discussed in terms of their structural properties.
Alan : Mühendislik
Dergi Türü : Ulusal
Benzer Makaleler | Yazar | # |
---|
Makale | Yazar | # |
---|