AMAÇ: Bu çalışmanın amacı üniversal adezivlerin uygulama zamanlarının uzatılmasının, makaslama bağlanma dayanımı üzerine etkisinin araştırılmasıdır. GEREÇ VE YÖNTEM: Çalışmamızda 63 adet çürüksüz insan molar dişi kullanıldı. Okluzal kısımda yüzeyel dentin açığa çıkarıldıktan sonra örnekler, rastgele, kullanılacak olan üç farklı adezivin farklı uygulama sürelerine göre (5 sn, 10 sn, 20 sn) 9 gruba ayrıldı (n=7) (1. Single Bond Universal, 2. One Coat 7 Universal, 3. All-Bond Universal) . X-trafil bulk-fill kompozit kullanılarak tek tabaka halinde 4 mm yüksekliğinde ve 3 mm çapında kalıplar yardımıyla restoratif kısım tamamlandı ve LED cihazıyla polimerize edildi. Örnekler 24 saat 37oC suda bekletilip üniversal test cihazına (Instron 3344, Instron Corp, Wilmington, ABD) yerleştirildi. Veriler ANOVA ve Duncan testleri ile 0.05 anlamlılık düzeyinde analiz edildi. BULGULAR: En yüksek (8.35±1.90) ve en düşük (4.99±2.67) makaslama bağlanma dayanım değerleri All-Bond’ da, 20 saniye ve 10 saniye uygulama süreli gruplarda gözlenmiştir. All-Bond grubunda istatistiksel anlamda farklılık gözlenirken (p<0.05), diğer gruplarda istatistiksel olarak anlamlı bir farklılık bulunamamıştır (p>0.05). SONUÇ: Uygulama süresinin arttırılması All-Bond grubunda makaslama bağlanma dayanımını anlamlı oranda yükseltmiştir (p<0.05). Single Bond Universal ve One Coat 7 gruplarında ise istatistiksel olarak anlamlı bir farklılık görülmemiştir (p>0.05). ANAHTAR KELİMELER: Dentin, Makaslama bağlanma dayanımı, Uygulama süresi, Üniversal adeziv AIM: The aim of this study was to examine the effect of prolonged application time on the resin-dentin shear bond strength (SBS). MATERIALS AND METHODS: Caries-free sixty three human molars were used. After superficial dentin was exposed, samples were divided into nine groups (n=7) according to according to different application times (5 sec, 10 sec, 20 sec) of the three different adhesives (1. Single Bond Universal, 2. One Coat 7 Universal, 3. All-Bond Universal) Composite build-ups were made with X-trafil bulk-fill composite with the help of 4 mm height and 3 mm diameter molds as a single layer and polymerized with a light-emitting diode (LED). After immersion in water at 37°C for 24 h, the shear bond strength were measured by using with the universal testing machine (Instron 3344, Instron Corp, Wilmington, ABD). The results were analyzed statistically by using one-way ANOVA and Duncan’s post-hoc analysis at a significance level of 0.05. RESULTS: The highest and the lowest SBS values were observed in the All bond groups (8.35±1.90) and (4.99±2.67) applied 20s and 10s. A statistically significant difference was observed between All-bond groups (p<0.05). There was no significant difference in the other groups (p>0.05). CONCLUSION: Increasing the application time significantly improved the bond strength of All-bond group however, it had no significant effect on the bond strength of Single Bond Universal and One Coat 7 groups. KEYWORDS: Dentin, Shear bond strength, Application time, Universal adhesive
Objective: The purpose of this study is to investigate the impact of the extension of the time of application of university adjectives on the resistance of the association. WORK AND METHOD: In our study, 63 unclean human molar females were used. After the surface dentin was revealed in the occulus part; the samples were divided into 9 groups (n=7) according to the different time of application of the three different adjectives to be used randomly (5 s, 10 s, 20 s). The Single Bond Universal, 2. One Coat 7 Universal. The All-Bond Universal The restorative part was completed with the help of patterns of 4 mm height and 3 mm diameter in a single layer using X-trafil bulk-fill composite and polymerized with a LED device. The samples were kept in 37oC water for 24 hours and placed on the universal test device (Instron 3344, Instron Corp, Wilmington, USA). The data was analyzed at 0.05 significance levels with the ANOVA and Duncan tests. Results: The highest (8.35 ± 1.90) grid (4.99 ± 2.67) grid binding resistance values have been observed in All-Bond, 20 seconds and 10 seconds of application time groups. In the All-Bond group, statistical differences were observed (p<0.05), but statistically significant differences were not found in other groups (p>0.05). The extension of the application time has significantly increased the grinding connectivity resistance in the All-Bond group (p<0.05). In the Single Bond Universal and One Coat 7 groups there was no statistically significant difference (p>0.05). The aim of this study was to examine the effect of prolonged application time on the resin-dentin shear bond strength (SBS). MATERIALS AND METHODS: Caries-free sixty three human molars were used. After superficial dentin was exposed, samples were divided into nine groups (n=7) according to according to different application times (5 sec, 10 sec, 20 sec) of the three different adhesives (1. The Single Bond Universal, 2. One Coat 7 Universal. All-Bond Universal) Composite build-ups were made with X-trafil bulk-fill composite with the help of 4 mm height and 3 mm diameter molds as a single layer and polymerized with a light-emitting diode (LED). After immersion in water at 37°C for 24 h, the shear bond strength were measured by using with the universal testing machine (Instron 3344, Instron Corp, Wilmington, USA). The results were analyzed statistically by using one-way ANOVA and Duncan's post-hoc analysis at a significance level of 0.05. The highest and lowest SBS values were observed in the All bond groups (8.35±1.90) and (4.99±2.67) applied 20s and 10s. A statistically significant difference was observed between All-bond groups (p<0.05). There was no significant difference in the other groups (p>0.05). CONCLUSION: Increasing the application time significantly improved the bond strength of All-bond group; however, it had no significant effect on the bond strength of Single Bond Universal and One Coat 7 groups. Keywords: Dentin, Shear bond strength, Application time, Universal adhesive
AMAÇ: Bu çalışmanın amacı; üniversal adezivlerin uygulama zamanlarının uzatılmasının, makaslama bağlanma dayanımı üzerine etkisinin araştırılmasıdır. GEREÇ VE YÖNTEM: Çalışmamızda 63 adet çürüksüz insan molar dişi kullanıldı. Okluzal kısımda yüzeyel dentin açığa çıkarıldıktan sonra; örnekler, rastgele, kullanılacak olan üç farklı adezivin farklı uygulama sürelerine göre (5 sn, 10 sn, 20 sn) 9 gruba ayrıldı (n=7) (1. Single Bond Universal, 2. One Coat 7 Universal, 3. All-Bond Universal) . X-trafil bulk-fill kompozit kullanılarak tek tabaka halinde 4 mm yüksekliğinde ve 3 mm çapında kalıplar yardımıyla restoratif kısım tamamlandı ve LED cihazıyla polimerize edildi. Örnekler 24 saat 37oC suda bekletilip üniversal test cihazına (Instron 3344, Instron Corp, Wilmington, ABD) yerleştirildi. Veriler ANOVA ve Duncan testleri ile 0.05 anlamlılık düzeyinde analiz edildi. BULGULAR: En yüksek (8.35±1.90) ve en düşük (4.99±2.67) makaslama bağlanma dayanım değerleri All-Bond’ da, 20 saniye ve 10 saniye uygulama süreli gruplarda gözlenmiştir. All-Bond grubunda istatistiksel anlamda farklılık gözlenirken (p<0.05), diğer gruplarda istatistiksel olarak anlamlı bir farklılık bulunamamıştır (p>0.05). SONUÇ: Uygulama süresinin arttırılması All-Bond grubunda makaslama bağlanma dayanımını anlamlı oranda yükseltmiştir (p<0.05). Single Bond Universal ve One Coat 7 gruplarında ise istatistiksel olarak anlamlı bir farklılık görülmemiştir (p>0.05). ANAHTAR KELİMELER: Dentin, Makaslama bağlanma dayanımı, Uygulama süresi, Üniversal adeziv AIM: The aim of this study was to examine the effect of prolonged application time on the resin-dentin shear bond strength (SBS). MATERIALS AND METHODS: Caries-free sixty three human molars were used. After superficial dentin was exposed, samples were divided into nine groups (n=7) according to according to different application times (5 sec, 10 sec, 20 sec) of the three different adhesives (1. Single Bond Universal, 2. One Coat 7 Universal, 3. All-Bond Universal) Composite build-ups were made with X-trafil bulk-fill composite with the help of 4 mm height and 3 mm diameter molds as a single layer and polymerized with a light-emitting diode (LED). After immersion in water at 37°C for 24 h, the shear bond strength were measured by using with the universal testing machine (Instron 3344, Instron Corp, Wilmington, ABD). The results were analyzed statistically by using one-way ANOVA and Duncan’s post-hoc analysis at a significance level of 0.05. RESULTS: The highest and the lowest SBS values were observed in the All bond groups (8.35±1.90) and (4.99±2.67) applied 20s and 10s. A statistically significant difference was observed between All-bond groups (p<0.05). There was no significant difference in the other groups (p>0.05). CONCLUSION: Increasing the application time significantly improved the bond strength of All-bond group; however, it had no significant effect on the bond strength of Single Bond Universal and One Coat 7 groups. KEYWORDS: Dentin, Shear bond strength, Application time, Universal adhesive
Dergi Türü : Ulusal
Benzer Makaleler | Yazar | # |
---|
Makale | Yazar | # |
---|